Tower Fall Protection Is More Than a Harness: Lessons From a 2025 Fatality and 2026 OSHA Citations

A 2025 telecommunications tower fatality and subsequent 2026 OSHA citations offer a practical reminder: wearing a harness is not the same as having an effective fall-protection system. The critical questions are whether workers know how to select, connect, inspect, and use their equipment—and whether supervisors verify those practices before anyone climbs.

What is documented—and what is not

According to a March 5, 2026 report by industry publication Wireless Estimator, a 46-year-old technician died following a fall from approximately 50 feet at a Texas internet tower on July 14, 2025. The publication reports that OSHA issued three serious citations to Trace Wireless in January 2026, addressing fall-protection training, training certification records, and proper use of equipment. These are reported enforcement allegations; the available reporting does not establish the final legal disposition or conclusively identify the immediate mechanism of the fall. Do not infer that a particular connector, anchorage, or harness component failed without evidence.

Source: Wireless Estimator, March 5, 2026. OSHA’s communication tower employer letter independently emphasizes employer duties to provide, train, supervise, and enforce effective fall protection.

Five field controls to verify before climbing

  • 1. Connection and competency: Have each climber demonstrate the actual tie-off method for the structure, transitions, work positioning, and fall arrest. Inspect harnesses, connectors, energy absorbers, anchorages, and compatibility; maintain continuous protection appropriate to the task. A training certificate alone is not a field demonstration.
  • 2. Rescue readiness: Identify the specific rescue method, trained rescuers, equipment, access route, communications, emergency contacts, and retrieval time considerations before ascent. Do not treat a generic 911 instruction as a complete elevated rescue plan.
  • 3. Structural and rigging hold points: Confirm the approved structural assessment and modification sequence before removing or loosening members. Verify gin-pole/hoist configuration, rated capacities, rigging inspection, load path, exclusion zones, and dropped-object controls. Stop if installed conditions differ from the approved plan.
  • 4. RF, electrical, and weather exposure: Confirm carrier coordination and transmitter status or controlled RF exposure zones; assess energized equipment and isolation needs; monitor lightning, wind, heat, and visibility against task-specific limits. A personal RF monitor supplements—not replaces—an exposure-control plan.
  • 5. Contractor coordination: Establish a single field lead, scope boundaries, competent-person responsibilities, stop-work authority, crew communications, and a process for notifying all affected contractors when conditions change.

Make the pre-climb JHA a decision tool

Assess six interacting factors: task (climb, antenna swap, reinforcement); human factors (training, fatigue, communication); system state (tower condition, transmitter and equipment status); energy (gravity, suspended loads, electrical and RF); logic/sequence (tie-off transitions, rigging, removal and rescue steps); and site/environment (weather, access, other crews and public exposure). Before each critical transition, confirm that the controls assumed in the planning JHA still exist in the field JRA.

For structural modification, rigging changes, unexpected antenna configurations, or loss of a designated anchor, stop and obtain competent/engineering review before proceeding. Document the revised method and brief every affected worker. A successful lift or climb does not prove an uncontrolled method was safe.

Regulatory requirements versus consensus guidance

Enforceable: Applicable federal OSHA provisions—including 29 CFR 1910.268 for covered telecommunications work, relevant 1910 or 1926 fall-protection and training provisions, and other task-specific requirements—depend on the work and employment circumstances. OSHA’s communication tower guidance describes hazards but is not itself a new tower-specific regulation. Consult OSHA’s communication tower safety review and tower construction inspection guidance.

Consensus and industry guidance: ANSI/ASSP A10.48 and ANSI/TIA-322 offer important tower construction, rigging, and engineering practices. They are not automatically federal regulations; contract language, incorporation by reference, and the circumstances of a particular job can affect their significance. The Texas Department of Insurance’s tower safety guidance also provides practical reminders about climbing, weather, and RF controls.

The supervisor’s final question

Before authorizing ascent, ask: Can this crew demonstrate that every critical connection, load path, exposure control, and rescue assumption has been verified for this tower today? If not, the job is not ready to start.

Read more tower safety insights at https://ursafetypro.com.


Discover more from SAFETY TRAINING & CONSULTING SERVICES

Subscribe to get the latest posts sent to your email.

Leave a Reply